Repair B300 Hot Water Heaters

Amendment / Modification

This amendment (0001) to solicitation FA6670-26-B-0001, "Repair Hot Water Heaters B300," incorporates several new attachments into Section J of the solicitation. The effective date of this amendment is March 26, 2026.

Specifically, the following attachments have been added:

• Attachment 5: B300 EL Panel Schematics E-17 (dated April 11, 2020)

• Attachment 6: B300 Mech room layout (dated April 11, 2020)

• Attachment 7: B300 Mechanical M16-M22 (dated April 11, 2020)

• Attachment 8: B300 Mechanical Room (dated April 11, 2020)

• Attachment 9: Floor Plans 300 304306308 (dated March 26, 2026)

• Section J of the solicitation has been updated to include the attachments listed above.

• All other terms and conditions of the original solicitation, as previously amended, remain unchanged.

• The amendment does not explicitly state whether the proposal deadline has been extended. Offerors are instructed to acknowledge receipt of this amendment.

Form / Attachment / Pricing Sheet

This document contains "As Built" panel schedules for electrical distribution panels P11 through P16. It details the circuits, voltage, amperage, and load designations for each panel.

• Panel Identification: Each section is clearly labeled with the panel number (P11-P16), type (3 Phase, 4 Wire), voltage (120/208V), and main breaker rating (225 AMP M.L.O.).
• Circuit Details: For each panel, individual branch circuits are listed with their designation (e.g., RM 154 MICROWAVE, DRYER, AHU-2), phase load in volts-amps, amperage, and number of poles.
• Total Load Calculations: Each panel schedule includes a "TOTAL" line summarizing the connected KVA and demand KVA.
• Notes: A note indicates that an asterisk denotes a switch-rated circuit breaker. Another note encourages value engineering.

This document provides critical technical specifications for the electrical systems associated with the opportunity. Bidders can use this information to understand the existing electrical infrastructure, assess the scope of work related to electrical components, and accurately price their proposals. It is essential for any work involving the building's electrical distribution.

Form / Attachment / Pricing Sheet

This document is a floor plan or layout drawing, likely related to mechanical or electrical systems within a building. It serves as a visual reference for the placement and identification of various equipment and components.

• Identifies and labels equipment such as Air Handling Units (AHU-1, AHU-2), Inverters, Timeclocks, Sump Pumps, and various components labeled CP-1 through CP-5.
• Shows electrical and mechanical pathways (e.g., P11-1, P12-3).
• Includes labels for areas like "MSB" (Main Switchboard), "DACP" (Data Acquisition and Control Panel), "TTB" (Terminal Transfer Box), and "CATV" (Cable Television).
• Indicates power ratings for some equipment (e.g., 2.2KW, 3.7KW).
• References various notes (Note 2, Note 3, Note 4, Note 5, Note 11, Note 12) which would provide further detail.

This drawing is crucial for bidders to understand the physical layout and spatial requirements of the systems involved in the opportunity. It helps in visualizing the installation, maintenance, or upgrade work, and understanding the context of other technical specifications or requirements provided in related documents.

Form / Attachment / Pricing Sheet

This document contains "As Built" mechanical drawings for the Lodging Facility at Niagara Falls ARS, New York. It details the "As Built" conditions of the enlarged mechanical rooms on the first and second floors, as well as various mechanical equipment schedules and piping schematics.

• Mechanical Room Plans: Detailed layouts of mechanical rooms on the first and second floors, showing piping, ductwork, and equipment placement.
• Mechanical Equipment Schedules: Tables detailing specifications for Air Handling Units (AHUs), Boilers, Pumps, Exhaust Fans, Fan Coil Units, Unit Heaters, Chillers, and Water Heaters.
• Piping Schematics: Diagrams illustrating the layout and connections for chilled water, hot water, and domestic water systems.
• Details: Specific installation details for components like exhaust fans, louvers, coils, diffusers, and pumps.
• Notes and Legends: Explanations of abbreviations, pipe sizes, and installation requirements.

This document provides a comprehensive overview of the existing mechanical systems and their "As Built" configurations. Bidders involved in maintenance, repair, upgrade, or replacement of these systems would use this information to understand the current infrastructure, equipment specifications, and system layouts. It is crucial for assessing the scope of work, identifying existing conditions, and planning any necessary modifications or installations.

Form / Attachment / Pricing Sheet

This document is an "As Built" plumbing plan for the 1st Floor Area B, specifically detailing the soil, waste, and vent systems. It serves as a record of the installed plumbing infrastructure.

• Plumbing Plan: Shows the layout of pipes, fixtures (FD-1, FD-2, FD-3), and risers within Area B.
• Mechanical Room Details: Includes a "Soil Waste & Vent Riser Diagram" for the mechanical room and a "Submersible Sump Pump Detail" for the elevator pit.
• Notes and Specifications: Provides information on pipe sizes (in millimeters), legend references, section views, and details for miscellaneous plumbing.
• "As Built" Designation: Indicates that the plan reflects the final installed conditions.

This attachment provides critical visual and technical information regarding the existing plumbing infrastructure. Bidders involved in any work related to plumbing, mechanical systems, or renovations in this area should consult these plans to understand the current layout, pipe routing, fixture locations, and specific equipment details (like the sump pump). This is essential for accurate bidding, scope definition, and execution of any related tasks.

Form / Attachment / Pricing Sheet

This document provides detailed floor plans and room occupant information for Building 300 (Niagara Lodge - Visiting Quarters), Building 304 (Lodging Storage Facility), and Building 308 (Visitor's Lodging Facility) at the 914 AW - Niagara Falls IAP Air Reserve Station, NY.

• Building 300: Floor plans for the first and second levels, detailing room numbers, room types (e.g., Guest Room, Suite, Storage, Mechanical Room, Restrooms), and square footage for each space. It also includes a table with facility data such as Total Net SF, Total GSF, and Real Property Adjusted Gross SF.
• Building 304: Floor plans for the first level, showing room layouts, room types (primarily storage and utility spaces), and square footage. Facility data is also provided.
• Building 308: Floor plans for the first level, illustrating room configurations, room types (guest rooms, showers, laundry, living areas), and square footage. Facility data is included.
• Room Occupant Legend: Indicates spaces designated for '914 FSS Lodging' and 'No Net' (unoccupied or non-lodging space).

This document is crucial for bidders to understand the physical layout, size, and intended use of the facilities related to the opportunity. It provides specific details on the number and size of rooms, which is essential for assessing the scope of work, planning for renovations, maintenance, or operational requirements, and accurately estimating costs.

Statement of Work (SOW) / Performance Work Statement (PWS)

To furnish and install a new high-efficiency hot water heating system in Lodging Building 300, replacing the existing 300-gallon unit. The new system must meet or exceed the performance of the current system, including a first-hour rating capacity equivalent to 1,000,000 BTU/Hr, and exceed the current storage capacity of 300 gallons and 970 Gal/Hr recovery capacity.

• Furnish and install all necessary materials, equipment, components, parts, tools, labor, transportation, hauling, disposal/recycling, cleaning, inspection, testing, commissioning, training, and reporting.

• Submit materials and methods for approval prior to ordering and incorporation.

• Demolish, remove, and properly dispose of the existing hot water heater and associated components off-base.

• Provide and install all necessary ancillary components, including piping, joints, valves, pipe hangars, pipe insulation, and modify existing gas, hot/cold water, venting, condensate, and electrical systems as needed.

• Install a second hot water tank in-line with the heating system, sized to utilize space and not obstruct existing equipment.

• Install each hot water tank on a 4-inch-thick concrete pad.

• Replace an expansion tank, circulation pump, venting, and condensate piping.

• Address ancillary components with proper pipe insulation, labels/warnings, and painted surfaces.

• Provide an operation and maintenance training session with Base staff.

• Submit operation and maintenance manuals, warranties, and a list of spare parts.

• New system must meet performance equivalent to existing 1,000,000 BTU/Hr first-hour rating.

• New system must exceed existing 300-gallon storage capacity.

• New system must exceed existing 970 Gal/Hr recovery capacity at a 100°F temperature rise.

• Minimize facility downtime and hot water use for occupants during replacement.

• Not explicitly stated, but implied to be at Niagara Falls Air Reserve Station.

• Compliance with all applicable federal, state, and local laws, regulations, and standards.

• Submittals required for government review and approval prior to work initiation, including Work Schedule, Waste Logs, Product Data, Operation Manuals, Warranties, and Spare Parts.

• Environmental Protection: Collect, containerize, and properly dispose of all waste materials off-base. Ensure work area is clean daily. Characterize, store, package, label, mark, and placard wastes. Comply with Base standards for hazardous materials storage. Recycle or divert waste as practical. Submit quarterly Waste / Recycle Materials Log. Comply with Green Purchasing requirements.

• Asbestos and Lead Based Paint (LBP): Immediately contact 914 MSG/CEV and 914 MSG/SGPB if asbestos and LBP containing materials are suspected before disturbance.

Solicitation / RFP / RFQ

This solicitation is for the "Repair Hot Water Heaters B300" project located at Niagara Falls NY 14304. The government requires the contractor to furnish all labor, materials, equipment, and miscellaneous services to complete the repair, including demolition and disposal of the existing hot water tank, and provision of necessary valves, piping, venting, insulation, and electrical components for a complete installation. The contract will be a Firm Fixed Price (FFP) type.

• Repair of the B300 Hot Water Heaters.

• Demolish and dispose of the existing hot water tank.

• Provide and install new valves, piping, venting, insulation, and electrical components.

• Strict adherence to the attached Statement of Work, drawings, and associated documents.

• Contract Type: Firm Fixed Price (FFP).

• Estimated Magnitude: Between $100,000 and $250,000.

• Period of Performance: Within 10 calendar days after notice to proceed, and completion within 45 calendar days.

• Proposal Submission Deadline: April 17, 2026, by 2:30 PM local time.

• Bid Bond: SF Form 24 required.

• Evaluation: Award will be made to the responsible bidder whose bid conforms to the invitation and is most advantageous to the Government, considering only price.

• Proposal Acceptance: Request proposal acceptance through September 30, 2026.

• Submission Method: Bids must be mailed or hand-delivered. Faxed or e-mailed bids will not be accepted.

• Location for Bid Opening: 914th Air Refueling Wing (ARW), Niagara Falls ARS, NY 14304.

• This solicitation is a competitive 100% Service-Disabled Veteran-Owned Small Business (SDVOSB) set-aside.

• NAICS Code: 238220 (Plumbing, Heating, and Air-Conditioning Contractors).

• Size Standard: $19,000,000.00 Annual receipts.

• Offerors must be certified in SAM at the time of proposal submission.

• Real ID is required for base access.

• All personnel requesting access must have a Valid State Enhanced or Real ID or a Valid United States Passport.

• Electronic payment requests through Wide Area Work Flow (WAWF-RA) are mandatory.

Form / Attachment / Pricing Sheet

This document is a General Decision Number (GDN) for wage rates, specifically for building construction projects in Niagara County, New York. It serves as a prevailing wage determination required for federal construction contracts to ensure laborers and mechanics are paid at least the locally prevailing wage.

• Geographic Area: Niagara County, New York.
• Construction Type: Building Construction Projects (excluding single-family homes and apartments up to 4 stories).
• Classifications: Lists various construction trades and their corresponding hourly wage and fringe benefit rates (e.g., Asbestos Worker, Bricklayer, Carpenter, Electrician, Elevator Mechanic, Ironworker, Laborer, Painter, Plumber, Roofer, Sheet Metal Worker, Welder).
• Effective Dates: Wage rates are effective for specific periods, often updated annually or periodically (e.g., 01/02/2026, 07/01/2024, 05/26/2025).
• Executive Orders: Includes notes on Executive Order 13706 (Paid Sick Leave) and Executive Order 13658 (Federal Contractor Minimum Wage), outlining contractor obligations.
• Appeals Process: Details the process for appealing wage determinations.

Bidders must use this document to understand the minimum wage requirements for various trades on the project. This information is crucial for accurately estimating labor costs in their proposals and ensuring compliance with federal labor laws. The specific rates listed will directly impact the overall cost of the project and must be factored into bid calculations.

Form / Attachment / Pricing Sheet

This document is an "Acknowledgement, Agreement and Certification of Compliance with Contract Insurance Requirements" for Contract Number FA6670-26-X-00XX. It serves to ensure the contractor understands and agrees to maintain specific insurance requirements throughout the contract period, including any modifications or time extensions.

• The contractor certifies that required insurance has been obtained and will be maintained.
• It specifies that cancellation or material changes to insurance policies require at least 30 days' written notice to the Contracting Officer.
• It addresses New York State Workmen's Compensation Insurance or reciprocal agreements.
• It requires subcontractors to possess current certification of insurance.
• The agreement becomes legally binding and part of the referenced contract.
• Fields are provided for contractor and insurance company details, authorized signatures, dates, agent telephone numbers, and policy numbers.

Bidders should review this document to understand the insurance obligations that will be required upon contract award. It outlines the specific certifications and agreements related to insurance compliance that must be met.

Form / Attachment / Pricing Sheet

This document is an "Entry Access Request" form that must be completed for individuals requiring base access and e-mail to the Contracting Office. Upon receipt, a letter will be issued to the visitor center to grant access for personnel to the base. The completed form must be returned by the times and dates specified in the solicitation to gain base access.

• Company Name
• A table requiring the following information for each individual:
  • Name (last, first, mi) - Alphabetized list
  • State ID/Driver's License (# & State of Issue)
  • Enhanced or REAL ID (Y/N)
  • Date of Birth
  • Country of Citizenship
  • Passport # (if applicable)

Bidders must complete and submit this form for any personnel who will require access to the base. The form requires specific identification details for each individual. Federal guidelines as of May 7, 2025, state that all personnel requesting access must possess a Valid State Enhanced or Real ID, or a Valid United States Passport. An Entry Access List (EAL) should be submitted three (3) business days in advance to avoid delays.